Burkert Type 6013 User Manual download pdf (Page 3)

7. INSTALLATION

7.1. Safety instructions

DANGER!

Risk of injury from high pressure in the equipment!

• Before loosening the lines and valves, turn off the pressure and

vent the lines.

Risk of injury due to electrical shock!

• Before reaching into the system, switch off the power supply and

secure to prevent reactivation!

• Observe applicable accident prevention and safety regulations for

electrical equipment!

WARNING!

Risk of injury from improper installation!

• Installation may be carried out by authorized technicians only and

with the appropriate tools!

Risk of injury from unintentional activation of the system and

an uncontrolled restart!

• Secure system from unintentional activation.

• Following installation, ensure a controlled restart.

7.2. Fluid installation

Installation position: any, actuator preferably upwards.

Procedure:

→ Clean any possible dirt off the pipelines and flange connections.

→ Install a dirt trap to prevent malfunctions (0.2 ... 0.4 mm).

Pay attention to the flow direction of the valve: from 1 (P) →

2(A) (CFA) or from 1(P) → 2(B) (CFB).

Valve with threaded connection:

→ Use PTFE tape as sealing material.

NOTE!

Caution risk of breakage!

• Do not use the coil as a lifting arm.

→ Hold the device with a Open-end wrench on the body and screw

into the pipeline.

Valve with flanged connection:

→ Remove the cover plate.

→ Loosen the nut on the coil and remove coil.

english

WARNING!

Danger – escaping medium!

Leaking connections if seals not seated properly, if manifold uneven

or if surface quality of the manifold inadequate.

• Make certain the seals included with delivery are properly seated in

the valve.

• Ensure that the manifold is even.

• Ensure that the surface quality of the manifold is adequate.

→ Insert the seal into the body.

→ Screw the body onto the manifold (max. 1.5 Nm).

→ Attach the coil and screw on the nut (max. 5 Nm).

Seal

Nut

Coil

Cover plate

Manifold

7.3. Electric installation

WARNING

Risk of injury due to electrical shock!

•

Before reaching into the system, switch off the power supply and

secure to prevent reactivation!

•

Observe applicable accident prevention and safety regulations for

electrical equipment!

If the protective conductor contact between the coil and body is

missing, there is danger of electrical shock!

• Always connect protective conductor.

• Check electrical continuity between coil and body.

Note the voltage and current type as specified on the type

label.

Procedure:

→ Check that the seal is correctly seated.

→ Screw cable plug tightly onto coil (max. 1 Nm).

english

Control of pulse version

Correct polarity is essential to ensure that the device func-

tions: Note identification on the upper side of the coil.

Pulse duration at least 50 ms.

switch ON +

Terminal 1

Terminal 2

Protective conductor connection

Polarity Specifications Terminal connections

- Switch ON +

Valve (P seat)

will be opened

(+) on terminal 2,

(–) on terminal 1

+ Switch OFF -

Valve (P seat)

will be closed

(+) on terminal 1,

(–) on terminal 2

Use only cable plug without electrical wiring for pulse versions.

7.4. Rotation of coil

WARNING!

Electric shock!

If the protective conductor contact between the coil and body is

missing, there is danger of electrical shock!

•

Check protective conductor contact after installing the coil.

Overheating, Risk of fire!

Connection of the coil without pre-assembled valve will result in

overheating and destroy the coil.

•

Connect the coil with assembled valve only.

Nut

max. 5 Nm

O-ring

Fitting

The coil can be turned by 4 x 90° (for

block installation only 2 x 180°).

Procedure:

→ Loosen nut.

→ Turn coil.

→ Tighten nut with a open-end

wrench (max. 5 Nm).

+ switch OFF

english

1 2 3 4 5 6 7 8 9 10 11

Comments to this Manuals

No comments

Burkert Type 6013 User Manual Page 3

Comments to this Manuals

Related products and manuals for Accessories for water Burkert Type 6013